HS10
07-04-2009, 06:51 PM
Fun toy to play with...
Stabilizer is a patented, compact, lightweight, easy to install 2-axis flight stabilization system (Roll- and Nick-function) developed for modell helicopters and is based on the analysis of infrared datas in a spectral area, where the composition of the ground (grass, water, asphalt, snow etc.) and the solar radiation are almost not relevant. The Stabilizer gets connected between the rc-receiver and the Nick- und Roll-servos.
Stabilizer works in almost all weathers, on day and night. Light or direct solar radiation into the sensors have no influence. The infrared horizon has to be straight / near to straight or simmetrical. In even or in a slightly hilly site, also in a valley between two mountains it will perform well. Among building or in a forest between the trees the Stabilizer will work after the helicopter is above the houses / trees (usable infrared horizon).
Features of Stabilizer:
Stabilizes normal flight. (For normal- and inverted-flight stabilisation look at the Stabilizer 3D.)
As assistance for advanced and as „emergency switch“ for specialists.
For helicopters with and without flybar, also for multi-bladed systems.
For aerial photography helicopters.
Technical data:
Operating voltage: 4V to 10V.
Current draw max. 20 mA.
Additional technical data:
Compatible with all PPM-receiveres, all Futaba PCM 1024 and Futaba PCM 2048 G3-receivers and all JR/Graupner SPCM-receivers.
Compatible with analog and digital servos.
Sensibility can be set from the transmitter or from the control-unit trimmer.
Compatible with 2-Servos-90° and 3-Servos-120° swashplates, mechanically and electronically mixed, recognizes automatically the swashplate type, for 2 or 3 servos. 90° swashplates with 3 or 4 servos are not supported, trying to control such systems will cause mechanical or electronic damages!!! (For a H4 90° 4-servos-swashplate version see Stabilizer H4.)
Only for outdoor use.
Compact and lightweight:
Control unit 22 x 25 x 8mm, 11g
Sensor unit 28 x 34 x 9mm, 16g
Stabilizer is a patented, compact, lightweight, easy to install 2-axis flight stabilization system (Roll- and Nick-function) developed for modell helicopters and is based on the analysis of infrared datas in a spectral area, where the composition of the ground (grass, water, asphalt, snow etc.) and the solar radiation are almost not relevant. The Stabilizer gets connected between the rc-receiver and the Nick- und Roll-servos.
Stabilizer works in almost all weathers, on day and night. Light or direct solar radiation into the sensors have no influence. The infrared horizon has to be straight / near to straight or simmetrical. In even or in a slightly hilly site, also in a valley between two mountains it will perform well. Among building or in a forest between the trees the Stabilizer will work after the helicopter is above the houses / trees (usable infrared horizon).
Features of Stabilizer:
Stabilizes normal flight. (For normal- and inverted-flight stabilisation look at the Stabilizer 3D.)
As assistance for advanced and as „emergency switch“ for specialists.
For helicopters with and without flybar, also for multi-bladed systems.
For aerial photography helicopters.
Technical data:
Operating voltage: 4V to 10V.
Current draw max. 20 mA.
Additional technical data:
Compatible with all PPM-receiveres, all Futaba PCM 1024 and Futaba PCM 2048 G3-receivers and all JR/Graupner SPCM-receivers.
Compatible with analog and digital servos.
Sensibility can be set from the transmitter or from the control-unit trimmer.
Compatible with 2-Servos-90° and 3-Servos-120° swashplates, mechanically and electronically mixed, recognizes automatically the swashplate type, for 2 or 3 servos. 90° swashplates with 3 or 4 servos are not supported, trying to control such systems will cause mechanical or electronic damages!!! (For a H4 90° 4-servos-swashplate version see Stabilizer H4.)
Only for outdoor use.
Compact and lightweight:
Control unit 22 x 25 x 8mm, 11g
Sensor unit 28 x 34 x 9mm, 16g